20 Resources That Will Make You Better At Fiat 500 Replacement Key Cost
Fiat 500 Replacement Key Fob
It might be time to change the battery if the 500 remote key fob is not working. If you replace the battery, but it's still not working the issue could be elsewhere.
At United Locksmith, we specialize in making new keys for classic automobiles. We have the tools and parts required for this type of service.
Dead Coin Battery
A dead battery is the main reason for your Fiat 500 keyfob not locking or unlocking the doors. The key fob has the battery of a coin-cell that will drain quickly when it isn't being utilized frequently enough. If your remote began to show signs of weakness such as a loss in range and stopped working completely it is likely that the battery is dead.
Metal clips hold the battery securely in the key fob. If the clips are loose it can cause contact issues which will prevent your remote from receiving power. With a small flathead screwdriver, pry the retaining clip open to take out the battery and replace it with a new one. Make sure you use an alternative battery that has the same type of voltage, dimensions, and specification as the original battery.
The key fob may also be damaged or corroded by water exposure. Even a short bath in soapy water could cause damage to the electronic chip inside. It is recommended to keep your key fob in a dry area.
Water Damage
If your key fob doesn't work correctly, it could be due to water damage. The rubber seals on key fobs protect them from getting damaged by a tiny splash or drizzle of water. However, it's crucial to keep your keys from the washing machine, the ocean and the pool.
The key fob comes with an electronic chip that sends a signal to your car's immobilizer system. This is the reason why your 500 can start or lock, but should the chip become wet, it will no longer work.
Try cleaning the internal electronics of your key fob using isopropyl alcohol, or an electronic cleaner to determine whether they're still in good condition. However, it's best to get a replacement from a dealership rather than trying to repair a key fob that has been submerged in salt water.
A replacement fob can cost you a bit however, it's cheaper than having to have your Fiat 500 towed to a dealer and repaired there! In addition, you can do it yourself in a few easy steps. Be sure to have the correct type of battery before you attempt to open your key fob. This is a job that's much simpler than it appears and you can find step-bystep instructions online for almost any car key fob.
Faulty Chip
The chip that is contained in the key fob communicates with the car's immobiliser unit to ensure the vehicle is only able to start when the correct key is inserted. If fob programming is damaged, or corrupted the car will not start regardless of what you do.
A damaged chip could occur due to many reasons, but most often it is due to water damage or a dead battery. Regardless of the reason, it's recommended to delegate the job to a locksmith who will be able to repair the chip for you swiftly and at a low cost.
If your key fob stops functioning after exposure to clean water from the tap or rain, take out the battery and clean the electronic component with a towel to ensure it is fully dry before putting it back in. If the key fob still doesn't work, it is likely an issue with the chip and is required to be replaced.
Some people will turn to their dealer when in need of an entirely new Fiat key fob, but it can be a expensive option. If you are looking for a cost-effective way to have your Fiat key fob fixed then look no further than United Locksmith. We have the tools and experience needed to repair your Fiat fob in a timely and professional way.
Faulty Receiver Module
Fiat key fobs transmit an electronic signal to the vehicle, which will unlock and close doors (and start the car if it has an automatic transmission) up to 50 feet. However there are a few things that could cause the fob to stop functioning. This could be due to a dead coin battery damaged by water buttons, worn ones as well as a receiver module problem and signal interference or an electronic chip that is malfunctioning.
If the fob is in an area that has experienced extreme trauma (such as being dropped on the floor or washed in a washing machine) the fob may not be in a position to communicate with the Body Control Module (BCM) of the vehicle. The BCM is a security device that will only accept signals from genuine keys.
If this is the case, then you must replace your fob. A professional locksmith is able to handle all aspects of the replacement procedure and even program a new one for your 500. In fact, they could offer you a clone key that functions exactly the same as your original fob (and costs only a fraction of the price).